Exhibitors

Carturner enlivens the exhibition stand, creates attention and stop effect.

Carturner represent a spectacular turning display that will bring your car expo stand to the top. The spectators can focus on, observe and absorbe the displayed car design and details all way round from one position. An huge efforth in crowded busy surroundings. It is then easier for stand personel to approach prospects too. Through it’s noiceless turning Carturner enlivens the car and make it “ask for attention”. The low 8 cm. profile of the turner also represent a nice visual frame around the car.

The turner is accessable from all angles with the benefits of reduced manouvering, faster engine cut and less exhaust. It is then quite easy to access even with finished stand construction as it only require a 2,5 meter corridor for entry. With it’s 72 panel integrated rolls the load capacity exceeds 3,5 tonns and opposite to traditional turner concepts the load does not balance on center bearing. The surface-mount version is assembled on top of excisting floor and do not require deep anchoring. Rotating speed is 1 ful turn in 45 seconds. Special featured brushless engine package can be delivered with stepless speedcontrol from 1/2-1 turn in 45 Seconds.  The power package consist of 6 pieces powerful 50W/24V engines with individual transmissions. The turner will run even with only 2 operating engines.  We keep turners in stock in anti skid powder coated and brushed stainless steel finishes.

We hold stock of a variety of finishes and colors such as powdercoated grey or black and brushed stainless steel. The turntable can also be ready fitted with vinyl graphics ranging from discrete to spectacular.

Quality at all levels

Carturner is developed with an eye for quality and durability. All parts of the basic construction such as the spider are made of high quality lasercut stainless steel. The Central bearing is milled With CNC tools. Bolts og rolls are properly dimensioned. The engine package has a lot of extra Power. Carturner is made to turn – no mather what! You can even run it in field for 8-10 hours on a couple of car batteries.

Precision and material quality is an huge advantage when repeatedly installed throug rental for shows. The turner comes with a special welded steel cage solid enough to hold it collected as one unit. Either it’s stocked or in transit this reduce risk for damage and loss of components.  Net cage measures: weight app. 0,9 tonn, volume app. 4,5CBM.

Static versus dynamic displays

This video from Oslo Motor Show presents the difference between a static and a dynamic display quite well. The video was shot when the turner had been shut off for a while and suddenly was swithced on turning. Look in the left side of picture frame and watch the kids reaction.. Be also aware of the kid who starts filming (seen through doors). A dynamic display such as Carturner attracs attention by trigging the peripheral vision. One has natural brain reflex to automatically focus sight to detect if the moving object represent a threat. To avoid this reflex one must be prepared of the coming movement of object and consciously ignore it. Kids respond easier to moving objects. In this case the kids response lead to parents response. The video demonstrates how a sequential rotation can work better than a continous one in display setting as unexpected mooves better triggs attention than predictable ones. 

Technique and dimensions

Carturner “surface mount” measures 470 cm. (15 feet 4 inches) in overall diameter. The table itself measures 406,5 cm. (160 inches). It elevates less than 8 cm.(3 inches) in outer edge.  The electrical engines (6 pcs.) and wire harness are hidden under the surrounding access ramps. This way they are available for service without disassemble the heavy construction table itself. Carturner is delivered complete with low voltage converter that require AC input between 110-240 Volts.   Mounting hardware for fixing the “spider” to the floor is not included.

Standard engine package consist of brush engines with a set speed. As customization we deliver brushless engines with  stepless rotation speed control from 1/2 turn in 45 seconds. This package is more relevant to display use or in showrooms for the sake of employees working nearby an operating turner.

Price

Please contact us for quotation incl. shipping to your address.

Basic construction

The CARTURNER brand turntable is a Lazy Susan with two principal components the “spider” and the “pan”. The spider is the underlayment which consists of three stainless steel rings connected by six stainless steel spokes connecting to a Delrin center hub/bearing. The clips that connect the spokes to the rings are also made of stainless steel. The outer ring is approximately 1 foot wide and mounts the six motors, each one of which is located approximately at the end of one of the spokes. The outer ring also mounts the ramps, which cover up the motors and allow the easy transition onto the pan. The pan is a high density polyurethane foam/stainless steel sandwich. It has ten, pie shaped panels, which connect to each other by tongue and groove. They bolt to the solid aluminum hub which fits over the Delrin center bearing/hub on the spider. The pan is tapered to allow run off of water.

Wheel Sets

It has 70 individual wheel sets under the pan. Each wheel set has its own miniature suspension system. Each one of these wheel sets lines up and runs on one of the Three rings of stainless steel. Each wheel sets consist of a pair of sealed stainless steel bearings, a solid stainless steel axle, solid Delrin wheel, and a pair of polyurethane spring pads in a glass reinforced nylon cup. We tested different wheels materials for 2 years. The solid Acetyl/Delran™ wheels that we use had less wear, less friction, and less noise than solid aluminum. We feel they are well worth the extra cost. Hard wheels have a very high point pressure. Narrow wheels means all the load is concentrated in a very small area, which can crack or cause wearing of the concrete.We use a wide wheel and 70 of them to spread the load. The result is that a 120 lb.woman can push a 4000lb. car around by hand.

Electrical and DC Motors

The motors are 50W 24V DC motors, with reduction gear heads. Turning time is approximately 22 seconds for 180 degrees. There are six motors. Draw is approximately 2 amps per motor. The motors direct drive onto the outside of the pan. The polycarbonate motor suspension arms enclose the sprockets + chain. Tension is provided by a polyurethane spring. The ramps completely enclose the motors. The machine will run on 2 motors, but we put in 6 for redundancy. We have run these machines on grass, powered by 2 car batteries for more than 12 continuous hours.

Electrical Convertor Specifications

The converter is a 500W 24 volts UL listed package. The wireless controller is UL approved and is off the shelf (ACE hardware). All the connectors are Delco Sealed connectors. Our UL-approved Meanwell converter accepts anything from 60-260 volts and converts it to 24 volts DC. Because it is 24 volts DC, there are no safety concerns and no permit requirements.

Suspension System

No concrete is completely smooth unless it is machined. There are small undulations. Our polyurethane suspension pad suspension system makes sure the wheel is flat to the concrete surface. The fact that these wide, coated wheels run on the smooth, stainless spider further spreads the load and reduces friction.

Interchangeability

Every single part of the machine is interchangeable. Each and every part can be replaced in less than ½ hour. A motor is replaced in less than 5 minutes. Every metal part, including all nuts and bolts, except the drive wheel is stainless steel. All metal pieces are laser cut for precision.

Total Weight Capacity

We have not tested for total weight capacity. However, we have not been able to break a CARTURNER. We have driven semi-trucks, loaded scrap haulers, and loaded steel delivery trucks over a CARTURNER repeatedly with no ill effect. Maximum weight that we were able to fit on our CARTURNER was a 16,000-lb forklift. One strong man was able to spin the CARTURNER a complete revolution by pushing on the loading forks of the 8-ton forklift.

Load Distribution

Our turntables distribute load very well. We have run several of our CarTurners on grass, and gravel. We placed 7/17” Base Material under the spider.

Maximum Slope

Center of mass of our CarTurner is less than 1”. The maximum slope a car dealer has attempted is 30%, but this was an exotic car with a very low center of gravity. We would not recommend a high center of gravity SUV or jacked suspension vehicle on a steeply angled CarTurner since as the auto reaches a point where the side is parallel to the ground it might slide off the machine.

Dimensions and Weight

Total footprint: 15’ 4”; Turning surface: 13’ 4”; Height: 3” at edge; Shipping weight: Approximately 2007 lbs.; Shipping dimensions: 84” x 40” x 64”

Surface Mount Turntable vs. In-Ground Turntable

Our patented design can be flush or surface mounted, whereas old Technology turntables can only be mounted in-ground because of their profile. Since our Carturner brand turntable can be used either way, we have a preference for surface mount. As you drive onto the turntable you can feel it. Surface mount means you can also move the machine slightly if needed or remove it completely.

Why Stainless Steel?

If you live near the coast or in an area where they salt the roads, stainless steel is a must. Even though it costs four times what regular steel costs, we believe it is essential. If a stone in the tire scratches a galvanized turntable, it will then start rusting.

Static vs. Dynamic Loads

We believe static load is not the most important criteria. The real issue is that 100% of the inertia of the car must be transferred to the turntable. In other words, a 4000-5000 lb. car going from 10 mph to zero mph in just a few feet represents a dynamic load much greater than the car’s static load after it has come to rest. Because Carturners center of mass is less than 1” high and the load is spread across the platform, it distributes this inertia better than any other turntable Product.

Ask us

Please do not hesitate to contact us if you have further need for information or want us to look on a potential project. We have access to empirical data that can be helpful to detect such as potential return on investment, technical opportunities etc.